MECO's decorative universal type fan coil unit is a product suitable for vertical blowing or hoisting installation of horizontal air. Beautiful appearance, easy to integrate into a variety of decoration styles. How to install the general surface mounted fan coil? Let's introduce it as follows:

1，機組應由熟練該類產品及本地相關規定的專業人員安裝。

1. The unit shall be installed by professional personnel skilled in such products and relevant local regulations.

2，為了排除搬運中可能造成的意外情況，安裝前應對機組盤管進行（1.0Mpa)的探漏檢驗。

2. In order to eliminate the possible accidents during the transportation, the unit coil shall be tested for leakage (1.0MPa) before installation.

3，進行安裝之前，首先檢查前期的準備工作是否就緒，如風管、水管、電線接口以及機組固定螺桿等。

3. Before installation, first check whether the preparatory work is ready, such as air pipe, water pipe, wire interface and unit fixed screw.

4，立式機組安裝在水平地面上；臥式機組進行吊裝，建議客戶采用直徑6-8MM全螺紋螺桿配合平墊圈、彈簧墊圈和螺母進行固定，機組吊裝應保持牢靠，吊裝點應緊固且需有足夠強度以承受機組運行重量及運行時的振動，吊裝機組時應確保水盤坡向排水管5°以上，以利于冷凝水外流。

4. The vertical unit shall be installed on the horizontal ground; the horizontal unit shall be hoisted, and it is recommended that the customer fix it with 6-8mm diameter full thread screw and flat washer, spring washer and nut. The unit shall be hoisted firmly, and the hoisting point shall be tight and strong enough to bear the operating weight and vibration of the unit. When hoisting the unit, the water pan slope shall be more than 5 ° to the drain pipe It is good for condensate outflow.

5，機組安裝時，水管和機組的連接建議采用撓性接管和生膠帶密封，管道連接時不可用力過猛，扭力不應超過205.6N.M，避免扭裂漏水。

5. When installing the unit, it is recommended to seal the connection between the water pipe and the unit with flexible connecting pipe and raw tape. When connecting the pipe, do not use excessive force, and the torque should not exceed 205.6n. M, so as to avoid water leakage due to torsional crack.

6，機組的進水管上應安裝水過濾器，以免污物堵塞盤管；機組進水應該要經過軟化處理，以保證盤管的換熱效率。

6. Water filter shall be installed on the water inlet pipe of the unit to prevent dirt from blocking the coil; the water inlet of the unit shall be softened to ensure the heat exchange efficiency of the coil.

7，機組進出水管道應裝有閥門，一調節水流量及檢修時能夠切斷水源；管道應預保溫，以免闡釋冷凝水泄露。

7. The water inlet and outlet pipes of the unit shall be equipped with valves, which can cut off the water source when regulating the water flow and maintenance; the pipes shall be pre insulated to avoid the leakage of condensate.